Your ESD Flooring Solutions Provider
Login
/
Register
My Account
000
Checkout
Added to your cart
You do not have any items in your shopping cart at this time.
View All cart items
Products
What's New
Resources
Application Photos
Floor Qualification
Videos
ESD Vinyl Tile
Conductive ESD Vinyl Tile
Dissipative ESD Vinyl Tile
Conductive Rubber Tiles and Rolls
Dissipative Modular Carpet Tiles
Conductive Adhesive, Grounding and Weld Rod
Dissipative Floor Finishes
Statguard® Low-VOC Dissipative Floor Finish
Statguard® Dissipative Floor Finish
ESD Floor Maintenance Products
Statguard® Floor Stripper
Statguard® Floor Neutralizer
Statguard® ESD Floor Cleaner
Statfree® Dissipative Spray Buff
Statfree® Burnishing Restorer
Conductive Epoxy and Paint
Statguard® Conductive Epoxy
Statguard® Conductive Acrylic Paint
Shop from our other Desco
Industries websites:
Desco Europe
Asia
Questions And Answers
#
351
List All Questions
Search
List by Category
Question
Could you please tell me exactly how fast the electron/proton (static) travel within a : a) Conductor b) Human Body -Anonymous
Answer
A human body (outer surface of, e.g., skin) is a conductor. I assume what you meant by conductor is a very conductive material such as a metal surface. I also assume you are referring to an ElectroStatic Discharge (ESD) which takes the charged imbalance on the conductor and neutralizes it (i.e., drain it to ground) upon contact with ground. A quick answer is: Very very fast for metal ( ~ 2x10
^{-18}
seconds)Sort of fast for human body (> 2x10
^{-6}
seconds) A more specific answer is: assume the worst case, class 0, which has a 0 to 249 Volt tolerance. Applying the HBM, a conservative worst case capacitance would be 200 pF, twice that of the HBM and resistance of 10K? . Therefore the maximum power (P) level based on Ohm’s Law is P=V2/R (J/s) and the worst case HBM is ((249)2/10K)=6.2 Watts or Joules per second (Js-1). The maximum energy (E) stored in a worst case HBM capacitance (C) of 200 pF and at a maximum voltage (V) of 249 Volts, (using E=1/2 CV2), yields 6.2 ? J. The next concern is to relate energy to time. The time constant (? ) is the measure of the length in time, in a natural response system, for the discharge current to die down to a negligible value (assume 1% of the original signal). For an RC circuit, the time constant (? ) is equivalent to the multiple of the equivalent resistance and capacitance. In this case, the time constant (? ) of our RC circuit is (10K? )(200pF) or ? = 2 ? s. Discharging this energy upon touching a conductor at zero volts yields a current, (using I=P/V), of (6.2Js-1)/(249V) or 24.8 mA. To avoid damaging a class 0 ESDS device, the discharge current must be below 24.8 mA. Engineering in a "2x" safety factor, the maximum discharge current would be 12.4 mA. To maintain a discharge current below 12.4 mA, we need to look at our grounding equipment on the ESDS workbench. The rate at which 6.2 ? J of energy discharges is very important. To fast a discharge will lead to an ESD Event, which can electromagnetically be measured using a simple loop antenna attached to a high impedance input of a high-speed storage scope. The faster the discharge the greater the discharge current becomes as well as the emf (electromotive force) on the loop antenna from the EMI (ElectroMagnetic Interference). Table III depicts the discharge current for 6.2 ? J at varying discharge times. We are assuming lossless conditions during the discharge for worst case. For our example, to keep the discharge current below 12.4 mA, the discharge rate [from Table III] must be no quicker than 2.01 ? s. This energy-based-time constraint forms the lower boundary of the controlled discharge rate.
Related Categories:
Discharge Times
Electricity
If you have found this Q/A useful, please rate it based on its helpfulness.
This question has been rated:
(
0
% at
0
Ratings)